Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

模内装饰薄膜滞热对成型工艺的影响分析

以模内装饰技术(IMD)测试平板为研究对象，利用仿真和实验方法分析薄膜滞热的影响因素及薄膜滞热对成型工艺的影响规律。结果表明，薄膜滞热使动模侧模具温度场变化滞后于定模侧温度场，且在实验条件下达到8.6 ℃的最大温度差；薄膜滞热随着模具温度的增加而降低，随熔体温度和薄膜厚度增加而升高；薄膜影响熔体的充模与冷却，造成产品冷却不均的现象；薄膜滞热导致产品翘曲变形增加。     

长走向平行钒铁矿体协同开采方案研究

七角井矿区的钒、铁双层矿体走向长度超4 km且呈近似平行产出，下盘铁矿开采时损失贫化率高且上盘钒矿资源保护难度大。根据钒铁矿体走向长、近平行产出、厚度负相关、空区隐患大的开采技术条件 特征，采用平面分区、开采时序规划、采矿方法优化、区域稳定性控制等技术来实现钒铁矿协同开采。根据铁矿“中间厚、两端薄”、钒矿“中间薄、两端厚”的形态特征，将长走向的钒铁矿体分为东区、中区及西 区。工程空间上，双层矿体共用一套开拓、采准、运输等开采系统；开采时序上，在提高铁矿生产能力的同时保证了钒矿开采的时间灵活性；采矿方法上，东区及西区铁矿采用阶段矿房嗣后膏体微胶结充填法，中区 铁矿采用阶段矿房法转崩落法；此外，通过中区崩落顶板及上盘围岩，东、西区膏体充填方式保证了矿区开采时及开采后的区域稳定性。研究表明：所提出的协同开采方案使矿山铁矿设计开采储量增加了1 064.7万t ，膏体充填每年消耗干抛层、尾矿等矿山固废86万t以上，矿山安全及经济效益明显。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

折臂式随车起重机转台的拓扑优化设计

为了使折臂式随车起重机转台在最大应力不超过材料许用应力的前提下实现轻量化设计的目的,通过ADAMS软件仿真确定其极限工况,对转台进行静力学分析及拓扑优化。通过拓扑优化得到了理想的材料分布。基于优化结果调整转台结构,并对改进后的转台进行静力学分析。结果表明,优化后的转台能够满足实际的使用需求。同时,转台质量降低了12%,证明了优化设计的有效性和可行性,并为折臂式随车起重机的相关设计提供了一定的借鉴。     

钢渣热焖工艺及其对水泥性能的影响

本文研究了不同的热焖压力和时间对钢渣活性的影响和钢渣的不同掺量对水泥性能的影响.热焖工艺主要改善的是钢渣的膨胀性,熟料的7 d膨胀率为0.034％,未热焖的钢渣掺入15％和35％时膨胀率分别增加155.9％和311.8％,而1 MPa 1 h热焖后,相比于未热焖的情况,钢渣掺入15％和35％时分别降低77.0％、89.3％,钢渣掺量25％时,其3 d、7 d、28 d 抗压强度分别增加8. 0 MPa、3.6 MPa、2.7 Mpa,分别提高21.1％ 、11. 3％ 、6. 1％.     

气体裂变产物88Kr半衰期测量

为准确测定气体裂变产物⁸⁸Kr的半衰期，本工作从辐照铀靶中分离得到3个放化纯的⁸⁸Kr气体测量源。以⁸⁵Kr作内标监督源，¹³⁷Cs或⁵⁷Co作外标监督源，使用多个HPGe探测器分别采用单探测器位置接力法和双探测器位置接力法跟踪测量⁸⁸Kr 196.3 keV能量的特征γ射线，跟踪时间均在8个半衰期以上，以获得其半衰期数据。对3次独立测量数据用多种方法进行处理，最终得到⁸⁸Kr半衰期测定结果为（2.796±0.015） h。     

泳池式轻水反应堆内电磁线圈可控温辐照装置设计

本文设计了在泳池式轻水反应堆（简称泳池堆）内在线测量电磁线圈电性能的可控温辐照装置。采用MCNP程序进行中子物理计算，对泳池堆、线圈骨架的结构尺寸与物质组分进行了精细全尺寸模拟，得出辐照装置的发热功率和中子注量率。通过初步估算，使用ANSYS CFX进行了数值模拟，得出辐照装置内线圈在堆运行时的温度，并提出温度控制的方法。辐照装置采用铝材加工制造，并进行了垂直度测试、气压测试、检漏测试。增加了绝缘设计，将辐照装置与泳池堆之间进行绝缘。在线圈处预埋铠装热电偶，对线圈温度进行实时监测。在泳池堆内对电磁线圈进行辐照试验，结果表明，本文设计的辐照装置能满足电磁线圈在泳池堆孔道内进行辐照试验的要求，并可对电磁线圈进行实时温度控制。     

基于物联网的智慧林业可持续发展策略研究

随着我国科技的不断进步,在“互联网+”大数据的背景下,林业的智慧化发展是必经之路。虽然我国智慧林业的发展已经取得了一定的突破,但是仍然存在着许多问题。基于此,文章在物联网技术的基础上,对智慧林业的可持续发展策略进行探讨。